Product ID:EA 901 NA/L-3 PART A
MSDS Date:11/01/1991
FSC:8040
NIIN:00-116-0853
Kit Part:Y
MSDS Number: BRNGT

DEXTER ADHESIVES AND STRUCTURAL MATERIALS DIVISION

2850 WILLOW PASS ROAD
PITTSBURG, CA 94565-3299
US

Emergency Phone: 800-424-9300

Info Phone: 202-483-7616

Cage: 33564

DEXTER CORPORATION ADHESIVE & COATING SYSTEMS

312 BAY POINT, CA 94565-3299 US

Telephone: 202-483-7616

Cage: 33564

BISHPHENOL A/ EPICHLOROHYDRIN EPOXY RESIN

CAS: 25068-38-6

RTECS: KC2100000

Fraction By Weight: 40-70%

ALUMINUM POWDER

CAS: 7429-90-5

RTECS: BD0330000

Fraction By Weight: 15-40%

OSHA PEL 5 MG/M3

ACGIH TLV: 5 MG/M3

SILICON DIOXIDE

CAS: 112945-52-5

RTECS: VV7318000

Fraction By Weight: 5-10%

OSHA PEL 6 MG/M3

ACGIH TLV: 6 MG/3M

< 10 G/L (ESTIMATE) (TEST METHOD)

RTECS: 9999999VO

Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:IMMEDIATE EFFECTS: BRIEF CONTACT MAY
IRRITATE THE SKIN OR CAUSE A RASH. LONG TERM EFFECTS: REPEATED OR
PROLONGED SKIN CONTACT MAY RESULT IN ALLERGIC SENSITIZATION.
Effects of Overexposure:SKIN RASH, IRRITATION.
Medical Cond Aggravated by Exposure:SKIN SENSITIZATION

First Aid:EYE: FLUSH EYES WITH WATER FOR 15 MINUTES. IF IRRITATION
PERSISTS, GET MEDICAL ATTENTION. SKIN: WASH SKIN THOROUGHLY WITH
SOAP AND WATER. IF IRRITATION PERSISTS, GET MEDICAL ATTENTION.
INHALATION: REM OVE VICTIM TO FRESH AIR. IF SYMPTOMS PERSIST. GET
MEDICAL ATTENTION. INGESTION: DRINK PLENTY OF WATER. GET MEDICAL
ATTENTION IMMEDIATELY.

Extinguishing Media:DRY CHEMICAL OR HALON FIRE EXTINGUISHER OR WATER
SPRAY, FOAM OR FOG.
Fire Fighting Procedures:WEAR SCBA & FULL PROTECTIVE CLOTHING, SUCH AS
TURN-OUT GEAR. CARTRIDGE RESPIRATORS DON'T PROVIDE ADEQUATE
PROTECTION FOR FIRE FIGHTERS OR EXOTHERM MITIGATION.
Unusual Fire/Explosion Hazard:MAY LIBERATE LARGE QUANTITIES OF DENSE
FOUL- SMELLING SMOKE WHICH MAY CONTAIN UNIDENTIFIED TOXIC GASES.

Spill Release Procedures:WEAR PROTECTIVE CLOTHING, GLOVES, AND SAFETY
GLASSES. SCRAPE UP OR SHOVEL INTO DEPARTMENT OF TRANSPORTATION
(DOT) APPROVED WASTE CONTAINERS.

Handling and Storage Precautions:FOLLOW CURING SCHEDULE AS RECOMMENDED
IN PRODUCT LITERATURE.
Other Precautions:DO NOT CUT, GRIND, WELD OR DRILL ON OR NEAR THIS
CONTAINER.

Respiratory Protection:UNNECESSARY WITH ADEQUATE EXHAUST VENTILATION.
Ventilation:LOCAL EXHAUST VENTILATION AT THE POINT OF USE.
Protective Gloves:BUTYL RUBBER, PVC, NITRILE, RUBBER
Eye Protection:SAFETY W/SIDE SHIELDS, CHEMICAL GOGGLES
Other Protective Equipment:AN EYEWASH AND SAFETY SHOWER SHOULD BE
NEARBY AND READY FOR USE.
Supplemental Safety and Health
CONDITIONS TO AVOID: ...IN EXCESSIVE HEAT BUILD-UP CAUSING AN EXOTHERM.
THE EXOTHERM HAS THE POTENTIAL FOR RELEASE OF TOXIC GASES.

HCC:T4
Vapor Pres:NIL
Vapor Density:> 1 AIR= 1
Spec Gravity:<1 WATER = 1
Viscosity:3000-65000 P.
Solubility in Water:NEGLIGIBLE
Appearance and Odor:VISCOUS GRAY PASTE WITH SLIGHT ODOR

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, STRONG LEWIS OR MINERAL ACIDS.
Stability Condition to Avoid:AVOID MIXING RESIN (PART A) & CURING AGENT
(PART B) IN BATCHES > 1 LB UNLESS YOU PLAN TO USE IMMEDIATELY.
Hazardous Decomposition Products:CO, NOX, ALDEHYDES, ACIDS AND
UNDETERMINED ORGANICS.
Conditions to Avoid Polymerization:DON'T HEAT MIXED ADHESIVE > 125F
UNLESS CURING SURFACES TO BE BONDED. FAILURE TO OBSERVE THESE
PRECAUTIONS MAY RESULT...

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.